THIS BLOG IS DEAD.

NOTE 23 January 2014: New posts are no longer posted to this blog. New stuff at my new blog, http://urbanadventureleague.wordpress.com/ Please go there! All old and new posts are there, and you can also comment, too!

Thursday, February 24, 2011

The Raleigh Wayfarer Saga, Part 7: As finished as she'll be for now, and DYNO LIGHTING!

Tuesday after work I rolled myself and the Raleigh Wayfarer down to the Stephens Addition neighborhood* of SE Portland. There I found Mr. Raving Bike Fiend from the Great White North waiting for me. Today we were going to tackle the last major step of the Raleigh Wayfarer Restoration Project: mounting and hooking up my generator powered lighting!

But first, a couple of minor adjustments. Replace the 19 tooth rear cog with a 20 tooth, which reduced the "gear inches" by 5 inches, meaning the gearing will be lower than it was. Also, installation of a white chain to replace the original. And a "hack" on the rack: rings clamped on with hose clamps.  This allows for modern panniers with a bottom "hook" to be able to be securely attached to the rack.
Have I gone over the line with the white chain?
And the bags match!

A close up of the hook attaching to the ring.

And now for the lights! 

I purchased two lights from Velo-Orange.  The headlight is a Spanninga Micro FF LED Dyno Headlamp with Safe Stop.  The tail light is the Spanninga Pixeo XS Fender Dyno Taillight with Safe Stop.  And I will freely admit, the reason I picked these two was because they were the most economical choice I could find, $42 and $20 respectively.  I know the old adage "you get what you pay for" definitely applies to dyno lighting.  But I have a budget to work with, and the Raleigh is intended as an around-town/"commuter".  When I get dyno lighting on the Long Haul Trucker, I intend to go for more fancy componentry.

And I know what you're thinking:** "Why didn't Shawn go for a more 'retro' light to go with the aesthetic of the vintage English 3-Speed?"  I did think about that, but all the ones I saw used Halogen bulbs, which are not as bright as a modern LED and suck up a lot of juice.  And the LEDs I've seen have a "standlight" function, where a capacitor will provide power for the light for several minutes after the wheel stops moving.  I'll take practicality over aesthetics, since this is supposed to be an everyday bike, not a show piece.***
I could've removed the reflector, but I like it.

I was hoping that the generator lighting installation would go smoothly, but of course it didn't.  The first and biggest hurdle was figuring out how to mount the headlamp.  The provided bracket is designed to mount to the front brakes.  The problem is the bolt that attaches front brake to fork is just long enough for its intended purpose, no extra room.  So Keith and I rode to the closest hardware store to get a longer bolt.  We got back to find out that the threading on the new longer bolt did not match the older bolt, due to the peculiarities of old Raleighs and their 26 threads per inch.

So as the day grew later, we rolled to a different hardware store that was still open.  Keith looked and looked for a serviceable bolt, but none was to be found.  In that moment of desperation, though, was a piece of brilliance from Keith, an appropriate mounting "hack".  We'd get two separate pieces of metal bracket, one smaller than the other, bolt it together, and the flat metal would be thin enough (but just barely) to fit onto the crowded brake bolt.  Problem solved!
Not the most elegant mount, but it works.  I like how the hole acts as an unintended cable guide.


Keith wired the front light to the dyno, and it worked fine!  Step one is done.  So we moved onto the mounting of the rear light to the fender and the wiring to the front light.

Everything connected, we spun the front wheel to test the rear light.  The front light was working, but nothing from the rear.  Crap.  Is it the light itself, or the wiring?

Keith tested the front light by connecting it directly to the dynohub, and it worked, so it was obviously the wiring.  After several troubleshooting steps, he figured out that we'd connected the wires to the wrong terminals, so a quick reversal and everything's working.

And now I have a bike with DYNO LIGHTS!

And how does it work?  Well, just fine, thank you very much.  I used the dyno lighting exclusively for the ride home.  The rear was bright and so was the front.  The light has a focused narrow beam, which isn't as wide as my EOS light on my helmet.  So I'd say it's fine for around town, but not recommended for trail riding or the like.  (The Over The Bars in Milwaukee blog has a nice review here.)  As for drag and vibration which is common with any hub generators, I didn't notice anything.  I'll give a more detailed review after a few weeks of use.  

Maybe I didn't notice any drag since I put a new cog on the back.  The change wasn't super significant, it wasn't like the 2nd gear felt like the 1st or anything.  But it was significant enough, as the bike felt peppier!  Hills that I had to drop to 1st were now tackleable in 2nd.  Did I mention how much fun I had on the bike ride home?


So now most everything is done.  There will be minor tweaks, but unless the rear wheel fails soon, there are no more major things that need to be done to my Raleigh Wayfarer.  I still want to touch up the scratches and repaint the rusted front fender, but that's all minor stuff.

And old Raleigh, you are a fine bike!

*See if you can figure out that one!
**Play along with me here.
***It won't be a showpiece with all those scratches.

6 comments:

  1. Very nice. My experience with hub dynamos is that the drag is imperceptible. My DL-1 front light has a sensor so the light comes on when it gets dark automatically. At the end of the day when the light fades I don't notice any difference in effort required to pedal when the light comes on. Plus mine is a more power-hungry halogen to boot.

    The drag is so little that the next time I do a dynohub conversion for myself I'm going to use and LED front lamp and just run it all the time.

    ReplyDelete
  2. Dyno Lighting that's awesome! Way beyond my capabilities - great job! Love the tires they look great on the blue Wayfarer, stands out nicely. Also, I can't believe the snow in your photos. Snow, rain and sleet in the forecast for us tomorrow.

    Happy weekend

    ReplyDelete
  3. Hello, Mr. Granton.

    First off, THANK YOU for the hose clamp & ring idea- it is exactly what I have been looking for to render old rat-trap rear racks panie-compatible.

    By chance do you have a recommended sourse for the rings you used on the rear rack? Also, perchance any more (/detailed) phoos of he installation? How do you keep the rings from rotating in/out from the centerline?

    Also, I miss your pages in Momentum... =(

    Many thanks,
    ~Robin
    Victoria, BC

    ReplyDelete
  4. Hey Robin--

    Thanks for the kind words!

    I don't remember anything specifically about those rings, just that they were something generic I picked up at the hardware store. The rings will naturally rotate a little bit in and out, but once you've mounted the pannier, they're not going to move. I'll try to get some more detailed photos at some point!

    ReplyDelete
  5. Do you have any pictures of where the wire attaches to the taillight? I thought that the wire attaches from inside the fender with the Pixeo, but your picture makes it look like the wire comes out of the fender and then to the Pixeo.

    ReplyDelete
  6. Glenn--No photos, sorry. You need two holes on the fender: one for the mounting bolt, one for where the wire goes in. Since my fender already had a hole for the reflector, plus two holes on either side, we decided to use the side holes rather than have to drill another hole into the fender.

    ReplyDelete

I'm no longer allowing new comments on this blog. You can comment on the exact same post on the new blog. Go find it over at http://urbanadventureleague.wordpress.com/

Note: Only a member of this blog may post a comment.